Aqualine Vs Villaboard: What To Line A Bathroom With In New Zealand

Both boards are accepted wet-area linings in New Zealand. In a tiled shower, both need a waterproofing membrane over them before a single tile goes on. So “which one is waterproof?” is the wrong question. The decision comes down to tile weight, stud spacing, which walls get painted and what the designer has drawn.

We line bathrooms with GIB Aqualine® and Villaboard across Auckland, Hamilton and Wellington, and plenty of jobs use both in the same room. Our post on which GIB® board goes where in your home covers the whole house. This one stays in the bathroom and goes wall by wall.

Two Linings, Two Different Materials

GIB Aqualine® is plasterboard. It has a water-resistant gypsum core and a green face paper, and it comes in 10mm and 13mm sheets. It is scored and snapped like any other GIB® board and stopped with the rest of the house.

Villaboard is a James Hardie product, a sanded fibre cement sheet. In New Zealand it comes in 6mm and 9mm. It is denser and harder than plasterboard, it is rated for impact, and it cuts with different tools.

Weight tells you a lot. A 2400 x 1200 sheet of 10mm Aqualine is about 23kg. The same sheet in 9mm Villaboard is about 36kg. You feel that difference carrying it up the stairs, and it shows again in what the wall will carry once it is up.

Shower Walls: Both Boards Need A Membrane

Most of the confusion sits here. A tiled shower wall does not stay dry because of the board behind it. Tiles and grout let small amounts of water through, so the Building Code’s acceptable solution for internal moisture treats fibre cement and water-resistant plasterboard the same way: both are absorbent, and both need a membrane under the tiles.

That membrane runs at least 1800mm up the shower walls from the shower floor. In a shower with no fixed enclosure, the wet zone is measured out to 1500mm from the shower rose. A curtain does not count as an enclosure.

We take care of that step through our waterproofing services in Auckland. The membrane goes on once the lining is fixed, and it has to cure before any tile adhesive touches it.

A membrane under a new tiled shower has been treated as critical building work that needs consent. Check with your designer or council before anyone lifts a tool.

Tile Weight Usually Makes The Call

Ask your tile supplier for the weight per square metre before the lining is ordered. Each manufacturer publishes limits, and the gap between them is wider than most people expect.

Lining Maximum Tile Weight Stud Centres Behind Tiles
10mm GIB Aqualine® 26kg/m² 600mm maximum
13mm GIB Aqualine® 40kg/m² 600mm maximum
6mm Villaboard 15kg/m², tiles up to 300 x 300mm 400mm maximum
9mm Villaboard 15 to 30kg/m² 400mm to 600mm
9mm Villaboard, heavier tiles Above 30kg/m² Support angles needed, per the manufacturer

Light ceramic wall tiles suit either board. Large porcelain and natural stone are where it gets interesting. Once the tile goes past what 13mm Aqualine carries, 9mm Villaboard with the right stud centres and support angles is the answer. We fix Villaboard linings in Auckland for exactly that kind of wall.

Thin 6mm Villaboard is the opposite case. It carries the least of the four, wants the closest studs and suits small, light tiles only.

Behind tiles, both boards are held with mechanical fixings. Aqualine is screwed at 100mm centres in tiled areas, and adhesive is not allowed to stand in for the screws. Villaboard behind tiles is fixed with fasteners only. The tile load hangs off those fixings for the life of the bathroom.

Vanity Walls, Bath Surrounds And Painted Walls

Away from the shower, most of a bathroom is a splash zone or simply a steamy room. The wall behind a vanity or beside a freestanding bath gets the odd splash, then dries. Here Aqualine is usually our pick, because it finishes like the rest of the house.

Aqualine takes standard GIB® stopping. That means the bathroom walls are stopped and painted with the same system as the hallway outside. Villaboard on a painted wall brings a second material with its own finishing requirements into a room that gains nothing from it.

A tiled splashback behind the vanity or along the bath still gets a membrane under the tiles. Paint does not waterproof a wall, so painted finishes stay out of the shower.

Ceilings are simpler. We fix Aqualine to the battens and it is painted.

What The Framing Needs First

The lining spec changes the carpentry, and that is far cheaper to know before the walls are closed in.

For Aqualine: studs at 600mm centres or closer, nogs no further apart than 1350mm, and framing timber below 18% moisture content. Internal corners in a tiled shower get a galvanised steel angle.

For tiled Villaboard: a tighter frame. Studs at 400mm for the 6mm sheet and 400mm to 600mm for the 9mm, depending on tile weight, with nogs at 800mm. The frame has to be straight to within 3mm to 4mm over three metres. A stiff fibre cement sheet will not pull a bowed stud into line.

In a renovation this matters early. If the existing studs are at 600mm and the plan calls for 6mm Villaboard under tile, extra studs go in first. Ask our GIB® fixing team in Auckland to check the framing against the lining spec before sheets are ordered, so that conversation happens with the builder well before lining day.

Cost: Where The Money Goes

The sheets are a small line in a bathroom budget next to the membrane, the tiles and the labour. What moves the price between these two linings is the work around them.

  • Framing. Closer studs and nogs for tiled Villaboard, which in an older house means extra carpentry.
  • Cutting. Fibre cement is slower to cut and needs dust control. Aqualine scores and snaps with a knife.
  • Handling. A 9mm Villaboard sheet is roughly half as heavy again as 10mm Aqualine.
  • Finishing. Aqualine is stopped with everything else. Painted Villaboard is finished as a separate job.

The membrane costs the same either way, because both boards need it. Ask for the lining to be priced wall by wall, so you can see what the heavier spec adds before you commit to the tile.

Cutting, Dust And Older Bathrooms

Fibre cement contains crystalline silica, and breathing in the dust from cutting it can cause cancer. The 6mm sheet can be cut indoors with a scoring knife, a guillotine or fibre shears. A circular saw never comes inside, and the 9mm sheet is cut outdoors only, with an M Class vacuum and a P1 or better respirator. Nobody dry sweeps the offcuts.

Strip-outs carry their own risk. Old sheet linings in bathrooms can contain asbestos, and you cannot tell by looking. If the house is old enough for it to be a possibility, get the old lining tested, and removed by a licensed asbestos removalist if needed, before the new board is booked.

When Each Board Gets Specified

  • A tiled shower with tiles up to 40kg/m² gets Aqualine and a membrane, in 13mm once the tiles pass 26kg/m².
  • Heavy porcelain or stone above that goes on 9mm Villaboard, with closer studs, support angles and a membrane.
  • Vanity walls and bath surrounds get Aqualine, with a membrane under any tiled splashback.
  • Ceilings get Aqualine, painted.
  • Commercial or high traffic wet rooms, where walls take knocks, suit Villaboard.

Get The Lining Sorted Before The Tiler Is Booked

Send us the plans and the tile selection before the membrane and tiles are ordered. Pro Fixing® fixes both linings, and our tiling contractors in Auckland can check the tile weight against the board on each wall, so nothing has to be relined later. We will come back with a measured quote inside five days for work in Auckland, Hamilton or Wellington.

Frequently Asked Questions

Can You Use Standard GIB® Plasterboard In A Bathroom?

We do not recommend it. GIB Aqualine® is the board made for wet areas, and even the dry walls of a bathroom take steam every day. We line the whole room in a wet-area board and keep standard sheets for bedrooms and living areas.

Is GIB Aqualine® Waterproof?

No. It is water resistant. It copes with humidity and the occasional splash far better than standard plasterboard, but it is not designed for spaces above 90% relative humidity, so group showers, steam rooms and indoor pools need a different lining system.

Should A Bathroom Ceiling Be 10mm Or 13mm Aqualine?

Batten spacing decides it. 10mm Aqualine needs ceiling supports at 450mm centres, and 13mm can span supports at 600mm centres. In a renovation we check the existing battens before ordering.

Can Aqualine Or Villaboard Be Used For Bracing In A Bathroom?

Villaboard can be part of a rated bracing system, and in wet areas those bracing fixings must be stainless steel. Aqualine is not to be used as bracing in showers or beside baths, so the bracing plan and the lining schedule need to be read together.

Can Aqualine Go Straight Onto A Brick Or Block Wall?

No. GIB Aqualine® is not fixed directly to masonry, over an existing lining or over a vapour barrier. On a masonry wall the board goes onto framing or battens first, and that framing still has to be below 18% moisture content before the sheets go up.

Lined interior wall with taped and partly stopped joints, capped plumbing outlets and a power point

Our Partners

Awci
Ws Train apprentice
Archipro
Professional Builder
MB
Haza
Carter
LBP
Bunning Warehouse
Placemaker
Dulux
Resene
Contact Us
close slider

    Get a Free Quote